How to Resurface a Concrete Pool Deck

Ready to spice up an old, worn out pool deck

Don’t worry; it is not necessary to tear out the old concrete. Resurfacing a pool deck can assist add color or create the look of natural rock. The possibilities are endless.

If you have an existing concrete pool deck but want to spruce it up or get rid associated with boring old gray appearance, there is an easy choice:

For a project that is successful proper planning is needed:

  1. Use only once this product, atmosphere, and area temperatures are above 50°F for a minimum of 24 hours.
  2. Remove all loose and international materials such as sealers, paints, curing compounds, or glues that will interfere with bonding. Here’s a tip: a 2,500 psi pressure washer shall remove most contaminants.
  3. just before application, fill any cracks larger than 1/8” (3.2 mm) using Sakrete Flo-Coat mixed to a consistency that is trowel-grade.
  4. Dampen tangible surface bringing it to a surface saturated dry (SSD) condition before application associated with material.


For colored base coat applications and stenciling:

  1. Mix the Flo-Coat as directed on the packaging.
  2. For color, follow the Sakrete Cement Color mixing guidelines adding the cement color pigment to the mixing water that is flo-Coat’s.
  3. After properly preparing the substrate, bring it to a SSD condition. Do not utilize a bonding representative.
  4. Pour the mixed material onto the surface and spread with a squeegee that is long-handled. If squeegee marks are evident, drag a bristle that is stiff through the material immediately  after using the squeegee. If done when the Flo-Coat is still fluid, this will evenly blend the product together.
  5. Do not allow material to spill into expansion and control joints because the integrity of these joints must be maintained.
  6. Permit the Flo-Coat to dry for 4 to 8 hours depending on the temperatures and conditions before laying the stencil.
  7. Attach the decorative concrete stencil to your surface utilizing small quantities of the supplied adhesive putty to help keep the stencil in place as needed. This will simply need to be done in the areas that are not lying close to the outer lining. Minor lifting is acceptable since the weight associated with product during spraying will push the stencils flat to your surface. The concrete that is decorative are designed to lap next to each length permitting the width needed.
  8. Once laying the attractive concrete stencil is completed, mix more Flo-Coat per blending directions. You may even color this material in cases where a specific color is desired. Sakrete Cement Colors may be used but needs to be mixed in the water first, and then poured within the dry product.
  9. Once concrete resurfacing mixing is completed, add the material to the spray gun hopper, and start spraying in a motion that is circular the stencil holding the hopper gun waist high (approximately 4 ft.). Working your way backwards, apply a layer that is thin of over the surface. Caution should really be taken to raise your feet while walking across the stencil to avoid getting your base pulling and caught or tearing the stencil.
  10. Multiple coats may be required to obtain the texture desired. Work in sections, permitting each coat to dry enough to support the past layer before re-spraying over it. This can help keep you from walking in freshly sprayed material.
  11. Each layer can be quite a color that is different numerous tones are desired, nonetheless care should be taken to keep each additional coating light and so the base layer is not completely covered.
  12. Allow a few moments setting if the knock down look is desired before lightly toweling the outer lining by having a flat steel trowel.

Begin removing the ornamental stencil concrete the Flo-Coat dries. Do not allow the Flo-Coat to dry prior to removing the stencil since it becomes quite difficult to remove and will tear, leaving piece that are dry. These pieces can additionally stick to the finished stenciled areas and will also be unsightly.

For more information visit California Clean & Seal

Leave a Reply

Your email address will not be published. Required fields are marked *